Skip to main content

ADAS Camera Calibration in Billings, MT

Get Free Quote Call Now

ADAS camera calibration realigns the windshield-mounted camera that drives lane-keeping and collision warnings, and A+ Glass LLC performs it on site in Billings.

ADAS Camera Calibration from A+ Glass LLC in Billings

A+ Glass LLC calibrates windshield-mounted ADAS cameras in Billings so lane departure and collision warning systems read the road accurately. We handle recalibration on site, often in the same visit as your glass work, serving Billings, MT drivers from Lockwood to Laurel without a dealership trip.

Get your free quote

Get my quote

What are the key facts about ADAS Camera Calibration?

Price range

Request an estimate

Turnaround

Most calibrations: 30-60 minutes, often same visit as glass work

Areas served

Billings, Lockwood, Laurel, and nearby Yellowstone County towns

Contact

(406) 598-8000

What does ADAS Camera Calibration include?

  • Pre-scan of the ADAS camera and related sensors
  • Static or dynamic recalibration matched to your vehicle's procedure
  • On-site calibration at your driveway, lot, or workplace
  • Verification that lane departure and emergency braking alerts respond correctly
  • Post-replacement camera alignment after new windshield installation
  • Plain-English walkthrough of what was adjusted and why

What affects the price of ADAS Camera Calibration?

Hourly pay for concrete finishers in Montana, May 2025

25th percentile $26.07, Median $29.63, 75th percentile $31.20.

Source: U.S. Bureau of Labor Statistics, Occupational Employment and Wage Statistics, May 2025, Cement Masons and Concrete Finishers (47-2051). Employer pay, not a price quote.

Where is ADAS Camera Calibration available?

We offer adas camera calibration to customers across the region. Tap any area for full local details.

Where can I read more about ADAS Camera Calibration?

See the work

All services

What do customers ask about ADAS Camera Calibration?

Common questions and tips from our work with Billings customers.

Do I need to recalibrate the camera after a windshield replacement?

If your vehicle has a camera mounted behind the windshield, most manufacturers require recalibration any time the glass is replaced. Even a slight mounting shift can make lane-keeping alerts read the road wrong. We handle the calibration on site in Billings, usually in the same visit as the new windshield, so you leave with the system reading accurately.

How should I care for the camera area after calibration?

Keep the camera lens and the glass around it clean, but never scrape or use harsh chemicals directly on the lens window. Wash that zone gently by hand. Avoid applying tint, film, or aftermarket accessories near the camera mount, since anything between the lens and the road can throw the readings off. If dash alerts start acting up, get it rechecked early.

Can I drive right away once the calibration is finished?

Yes. A dynamic calibration runs while the vehicle is driven at set speeds, so by the time the job is signed off, the system has already confirmed its readings on real roads. A static calibration uses a target board in a controlled setup before you drive. Either way, once we confirm the checks pass, you're clear to go about your week normally.

Static and dynamic calibration are not interchangeable

Vehicles specify one of two methods. Static calibration uses a printed target positioned a precise distance from the vehicle in a controlled space. Dynamic calibration depends on driving at specific speeds so the camera relearns lane markings. Most makers allow only the method they engineered for your model, which is why we follow the exact procedure your vehicle calls for rather than a shortcut.

Why your camera needs recalibration after any glass work

The camera sits on a bracket glued to the windshield, and its aim is measured in fractions of a degree. A new windshield, even a perfect install, resets that reference point. Around Billings, MT, where I-90 commutes and ranch-road washboard keep sensors working hard, an out-of-aim camera means late or false collision warnings. Recalibration restores the factory aim.

Common questions, straight answers

Will my new windshield need ADAS camera calibration?

Often, yes. Late-model vehicles that use a camera for lane departure or collision warnings need that camera recalibrated after new glass goes in. We handle the calibration as part of the job so your safety systems work the way the manufacturer intended.

Question not answered here? Talk to us

3348 Drury Lane, Billings, MT, 59105
Phone: 406-506-4735